CAT Series
CAT 3302 PVE/ST
Please Call for Pricing
Clean Bench - Class 100 - Full Exhausting
1) Top mounted fan/filter module
- Constructed of 16 ga, white epoxy painted steel
- Direct drive motor blower w/ (1) 1/2 HP, 110V, motor & electronic speed control developing 1200 CFM to twice the clean hepa filter SP, vibration isolated
- Hepa filter to be (1) 30" x 36" x 3", 95% Ashre, 2 3/4" separatorless media, gasket seal, aluminum frame
- Front mounted 35% disposable prefilters in anodized aluminum hinged grilles for incoming air
- 100 FC lighting hepa mounted to the front & back of the filter unit
- Perforated anodized aluminum diffuser w/ center slot open
- Control panel w/ switches for light & motor, pressure gauge for supply filter
2) Tubular steel support framework
- 1 3/4" x 1 3/4" x 16 ga welded SS tubing w/ levelers
- Rear panel to be painted steel
- Side panels to be 1/4" clear acrylic in anodized aluminum mounting trim
- Panels are sized for working area of 28 1/2" high
- Front hinged shield, 18" high
3) Independent worktable, 36" high
- Constructed of tubular, painted steel with 8" deep exhaust plenum
- Work deck of 16 ga, type 304 SS, fully perforated & supported from below
- Lower, washable prefilter below work surface
- No lower base cabinet
4) Rear exhaust duct
- 4" x 24"
- Constructed of 20 ga, painted steel
- Top mounted, manually operated exhaust & recirc dampers
5) Dimensions
- 40"w x 96"h x 36 1/2"d overall
- 35"w x 28 1/2" h x 30"d interior
Clean Bench - Class 100 - Full Exhausting
1) Top mounted fan/filter module
- Constructed of 16 ga, white epoxy painted steel
- Direct drive motor blower w/ (1) 1/2 HP, 110V, motor & electronic speed control developing 1200 CFM to twice the clean hepa filter SP, vibration isolated
- Hepa filter to be (1) 30" x 36" x 3", 95% Ashre, 2 3/4" separatorless media, gasket seal, aluminum frame
- Front mounted 35% disposable prefilters in anodized aluminum hinged grilles for incoming air
- 100 FC lighting hepa mounted to the front & back of the filter unit
- Perforated anodized aluminum diffuser w/ center slot open
- Control panel w/ switches for light & motor, pressure gauge for supply filter
2) Tubular steel support framework
- 1 3/4" x 1 3/4" x 16 ga welded SS tubing w/ levelers
- Rear panel to be painted steel
- Side panels to be 1/4" clear acrylic in anodized aluminum mounting trim
- Panels are sized for working area of 28 1/2" high
- Front hinged shield, 18" high
3) Independent worktable, 36" high
- Constructed of tubular, painted steel with 8" deep exhaust plenum
- Work deck of 16 ga, type 304 SS, fully perforated & supported from below
- Lower, washable prefilter below work surface
- No lower base cabinet
4) Rear exhaust duct
- 4" x 24"
- Constructed of 20 ga, painted steel
- Top mounted, manually operated exhaust & recirc dampers
5) Dimensions
- 40"w x 96"h x 36 1/2"d overall
- 35"w x 28 1/2" h x 30"d interior
CAT Series
CAT 3302-TT-PR-ST
Please Call for Pricing
NO SPEC AVAILABLE AT THIS MOMENT
NO SPEC AVAILABLE AT THIS MOMENT
NO SPEC AVAILABLE AT THIS MOMENT
NO SPEC AVAILABLE AT THIS MOMENT
NO SPEC AVAILABLE AT THIS MOMENT
CAT Series
CAT 5302 PDE
Please Call for Pricing
Class 100 Single pass Vertical Workstation
1) Top mounted fan/filter module
- Constructed of 16ga epoxy painted steel
- Direct drive motor blower w/ (1) 1/2 HP, 110v, motor & electronic speed control developing 1250 CFM to twice the clean hepa filter SP, vibration isolated
- Hepa filter to be (1) 30" x 60" x 3", 99.99% scan tested using PSL & laser particle counter, 2" separatorless media, gasket seal, aluminum frame, center divider w/ (2) plugged ports for upstream concentration readings
- Front mounted 35% disposable prefilters in aluminum hinged grilles for incoming air, non-adjustable
- 100 FC fluorescent lighting w/ acrylic eggcrate diffuser
- Control panel w/ switches for light & motor, pressure gauge for supply hepa filter, plugged port for adjustment of speed control
2) Tubular steel support framework
- 1 3/4" x 1 3/4" x 16 ga welded steel tubing, white epoxy painted w/ levelers
- Rear & side panels to be 20 ga, white painted steel
- Aluminum angle on top of frame to hold filter unit
3) Independent worktable, 36” high
- Constructed of 16 ga epoxy painted steel
- Work deck of 16 ga, type 304 SS, fully perforated
4) Factory testing w/ documents shipping with unit
5) Dimensions
- 64”w x 96”h x 36”d overall
- 60”w x 28 ½”h x 30”d interior
Class 100 Single pass Vertical Workstation
1) Top mounted fan/filter module
- Constructed of 16ga epoxy painted steel
- Direct drive motor blower w/ (1) 1/2 HP, 110v, motor & electronic speed control developing 1250 CFM to twice the clean hepa filter SP, vibration isolated
- Hepa filter to be (1) 30" x 60" x 3", 99.99% scan tested using PSL & laser particle counter, 2" separatorless media, gasket seal, aluminum frame, center divider w/ (2) plugged ports for upstream concentration readings
- Front mounted 35% disposable prefilters in aluminum hinged grilles for incoming air, non-adjustable
- 100 FC fluorescent lighting w/ acrylic eggcrate diffuser
- Control panel w/ switches for light & motor, pressure gauge for supply hepa filter, plugged port for adjustment of speed control
2) Tubular steel support framework
- 1 3/4" x 1 3/4" x 16 ga welded steel tubing, white epoxy painted w/ levelers
- Rear & side panels to be 20 ga, white painted steel
- Aluminum angle on top of frame to hold filter unit
3) Independent worktable, 36” high
- Constructed of 16 ga epoxy painted steel
- Work deck of 16 ga, type 304 SS, fully perforated
4) Factory testing w/ documents shipping with unit
5) Dimensions
- 64”w x 96”h x 36”d overall
- 60”w x 28 ½”h x 30”d interior
CAT Series
CAT 5302 PE
Please Call for Pricing
Class 100 Exhausting Vertical Workstation
1) Top mounted fan/filter module
- Constructed of 16ga epoxy painted steel
- Direct drive motor blower w/ (1) 1/2 HP, 110v, motor & electronic speed control developing 1250 CFM to twice the clean hepa filter SP, vibration isolated
- Hepa filter to be (1) 30" x 60" x 3", 99.99% scan tested using PSL & laser particle counter, 2" separatorless media, gasket seal, aluminum frame, center divider w/ (2) plugged ports for upstream concentration readings
- Front mounted 35% disposable prefilters in aluminum hinged grilles for incoming air, non-adjustable
- 100 FC fluorescent lighting w/ acrylic eggcrate diffuser
- Control panel w/ switches for light & motor, pressure gauge for supply hepa filter, plugged port for adjustment of speed control
2) Tubular steel support framework
- 1 3/4" x 1 3/4" x 16 ga welded steel tubing, white epoxy painted w/ levelers
- Rear & side panels to be 20 ga, white painted steel
- Aluminum angle on top of frame to hold filter unit
3) Independent worktable, 36” high
- Constructed of 16 ga epoxy painted steel
- Work deck of 16 ga, type 304 SS, fully perforated w/ lower 8” deep exhaust plenum
- Bottom lower cabinet w/ (2) hinged & gasketed doors, vented to the exhaust
4) Rear exhaust duct
- 4" x 24"
- Constructed of 14 ga, white painted steel
5) Factory testing w/ documents shipping with unit
6) Dimensions
- 64”w x 96”h x 36”d overall
- 60”w x 28 ½”h x 30”d interior
Class 100 Exhausting Vertical Workstation
1) Top mounted fan/filter module
- Constructed of 16ga epoxy painted steel
- Direct drive motor blower w/ (1) 1/2 HP, 110v, motor & electronic speed control developing 1250 CFM to twice the clean hepa filter SP, vibration isolated
- Hepa filter to be (1) 30" x 60" x 3", 99.99% scan tested using PSL & laser particle counter, 2" separatorless media, gasket seal, aluminum frame, center divider w/ (2) plugged ports for upstream concentration readings
- Front mounted 35% disposable prefilters in aluminum hinged grilles for incoming air, non-adjustable
- 100 FC fluorescent lighting w/ acrylic eggcrate diffuser
- Control panel w/ switches for light & motor, pressure gauge for supply hepa filter, plugged port for adjustment of speed control
2) Tubular steel support framework
- 1 3/4" x 1 3/4" x 16 ga welded steel tubing, white epoxy painted w/ levelers
- Rear & side panels to be 20 ga, white painted steel
- Aluminum angle on top of frame to hold filter unit
3) Independent worktable, 36” high
- Constructed of 16 ga epoxy painted steel
- Work deck of 16 ga, type 304 SS, fully perforated w/ lower 8” deep exhaust plenum
- Bottom lower cabinet w/ (2) hinged & gasketed doors, vented to the exhaust
4) Rear exhaust duct
- 4" x 24"
- Constructed of 14 ga, white painted steel
5) Factory testing w/ documents shipping with unit
6) Dimensions
- 64”w x 96”h x 36”d overall
- 60”w x 28 ½”h x 30”d interior
NO SPEC AVAILABLE AT THIS MOMENT
NO SPEC AVAILABLE AT THIS MOMENT
CAT Series
CAT 5302 SFE
Please Call for Pricing
CAT Series
CAT 6302 PDE
Please Call for Pricing
Class 100 Single Pass Workstation
1) Top mounted fan/filter module
- Constructed of 16ga epoxy painted steel
- Direct drive motor blower w/ (2) 1/3 hp, 110v, motor & electronic speed control developing 1500 CFM to twice the clean hepa filter SP, vibration isolated
- Hepa filter to be (2) 30" x 36" x 3", 99.99% scan tested using PSL & laser particle counter, 2" separatorless media, gasket seal
- Aluminum frame, center divider w/ (2) plugged ports for upstream concentration readings
- Front mounted 35% disposable prefilters in aluminum hinged grilles for incoming air, non adjustable
- 100 FC fluorescent lighting below hepa w/ acrylic eggcrate diffuser
- Control panel w/ switches for light & motor, pressure gauge for supply hepa filter, plugged port for adjustment of speed control
2) Tubular steel support framework
- 1 3/4" x 1 3/4" x 16 ga welded steel tubing, white epoxy painted w/ levelers
- Rear panel to be 20 ga, white painted steel
- Side panels of ¼” clear polycarbonate
- Aluminum angle on top of frame to hold filter unit
3) Independent worktable, 36” high
- Constructed of 16 ga epoxy painted steel
- Work deck of peforated 16 ga, type 304 SS
- No base cabinets
4) Dimensions
- 75”w x 96”h x 32”d overall
- 71”w x 28 ½”h x 30”d interior
Class 100 Single Pass Workstation
1) Top mounted fan/filter module
- Constructed of 16ga epoxy painted steel
- Direct drive motor blower w/ (2) 1/3 hp, 110v, motor & electronic speed control developing 1500 CFM to twice the clean hepa filter SP, vibration isolated
- Hepa filter to be (2) 30" x 36" x 3", 99.99% scan tested using PSL & laser particle counter, 2" separatorless media, gasket seal
- Aluminum frame, center divider w/ (2) plugged ports for upstream concentration readings
- Front mounted 35% disposable prefilters in aluminum hinged grilles for incoming air, non adjustable
- 100 FC fluorescent lighting below hepa w/ acrylic eggcrate diffuser
- Control panel w/ switches for light & motor, pressure gauge for supply hepa filter, plugged port for adjustment of speed control
2) Tubular steel support framework
- 1 3/4" x 1 3/4" x 16 ga welded steel tubing, white epoxy painted w/ levelers
- Rear panel to be 20 ga, white painted steel
- Side panels of ¼” clear polycarbonate
- Aluminum angle on top of frame to hold filter unit
3) Independent worktable, 36” high
- Constructed of 16 ga epoxy painted steel
- Work deck of peforated 16 ga, type 304 SS
- No base cabinets
4) Dimensions
- 75”w x 96”h x 32”d overall
- 71”w x 28 ½”h x 30”d interior
NO SPEC AVAILABLE AT THIS MOMENT
NO SPEC AVAILABLE AT THIS MOMENT
CAT Series
CAT 6302 SFE
Please Call for Pricing
Class 100 Single Pass Workstation
1) Top mounted fan/filter module
- Constructed of 16ga epoxy painted steel
- Direct drive motor blower w/ (2) 1/3 hp, 110v, motor & electronic speed control developing 1500 CFM to twice the clean hepa filter SP, vibration isolated
- Hepa filter to be (2) 30" x 36" x 3", 99.99% scan tested using PSL & laser particle counter, 2" separatorless media, gasket seal
- Aluminum frame, center divider w/ (2) plugged ports for upstream concentration readings
- Front mounted 35% disposable prefilters in aluminum hinged grilles for incoming air, non adjustable
- 100 FC fluorescent lighting below hepa w/ acrylic eggcrate diffuser
- Control panel w/ switches for light & motor, pressure gauge for supply hepa filter, plugged port for adjustment of speed control
2) Tubular steel support framework
- 1 3/4" x 1 3/4" x 16 ga welded steel tubing, white epoxy painted w/ levelers
- Rear panel to be 20 ga, white painted steel
- Side panels of ¼” clear polycarbonate
- Aluminum angle on top of frame to hold filter unit
3) Independent worktable, 36” high
- Constructed of 16 ga epoxy painted steel
- Work deck of solid 16 ga, type 304 SS
- No base cabinets
4) Dimensions
- 75”w x 96”h x 32”d overall
- 71”w x 28 ½”h x 30”d interior
Class 100 Single Pass Workstation
1) Top mounted fan/filter module
- Constructed of 16ga epoxy painted steel
- Direct drive motor blower w/ (2) 1/3 hp, 110v, motor & electronic speed control developing 1500 CFM to twice the clean hepa filter SP, vibration isolated
- Hepa filter to be (2) 30" x 36" x 3", 99.99% scan tested using PSL & laser particle counter, 2" separatorless media, gasket seal
- Aluminum frame, center divider w/ (2) plugged ports for upstream concentration readings
- Front mounted 35% disposable prefilters in aluminum hinged grilles for incoming air, non adjustable
- 100 FC fluorescent lighting below hepa w/ acrylic eggcrate diffuser
- Control panel w/ switches for light & motor, pressure gauge for supply hepa filter, plugged port for adjustment of speed control
2) Tubular steel support framework
- 1 3/4" x 1 3/4" x 16 ga welded steel tubing, white epoxy painted w/ levelers
- Rear panel to be 20 ga, white painted steel
- Side panels of ¼” clear polycarbonate
- Aluminum angle on top of frame to hold filter unit
3) Independent worktable, 36” high
- Constructed of 16 ga epoxy painted steel
- Work deck of solid 16 ga, type 304 SS
- No base cabinets
4) Dimensions
- 75”w x 96”h x 32”d overall
- 71”w x 28 ½”h x 30”d interior
NO SPEC AVAILABLE AT THIS MOMENT
NO SPEC AVAILABLE AT THIS MOMENT
NO SPEC AVAILABLE AT THIS MOMENT
NO SPEC AVAILABLE AT THIS MOMENT
CAT Series
CAT 8302 SFE
Please Call for Pricing